Modeling and realization of real time electronic countermeasure simulation system based on SystemVue

In this paper, we proposed a new design scheme of real time electronic countermeasure simulation system. This paper mainly expounds the modeling and realization methods of each part of the whole simulation system, and the real-time property of system has been lucubrated. Electronic countermeasure simulation system is the key part of military training of individuals; it can also allow the realistic evaluation of the performance of modern equipments and techniques. As a proof, we have drawn up a series of simulation scenarios, such as radar electronic reconnaissance simulation scenario, to explain the feasibility and the superiority of our modeling scheme in this paper.     

Responses of HFR-LWC beams under close-range blast loadings accompanying membrane action

The load-carrying capacities and failure patterns of reinforced concrete components can be significantly changed by membrane effects. However, limited work has been carried out to investigate the blast resistance of Hybrid Fiber Reinforced Lightweight Aggregate Concrete (HFR-LWC) members accompanying membrane action. This paper presents a theoretical approach to quantitatively depicting the membrane behavior and its contribution on the behavior of HFR-LWC beams under close-range blast loadings, and the suitability of the proposed model is validated by a series of field tests. An improved Single-Degree-of-Freedom (SDOF) model was employed to describe the dynamic responses of beam-like members under blast loadings accompanying membrane action, where the mass-load coefficient is determined according to the nonuniformly distributed load induced by close-range explosion, and the membrane action is characterized by an in-plane (longitudinal) force and a resisting moment. The elasto-plastic and recovery responses of HFR-LWC beams under the combined action of blast load and membrane force were analyzed by the promoted model. A specially built end-constrain clamp was developed to provide membrane action for the beam member when they are subjected to blast load simultaneously. It is demonstrated that the analytical displacement-time histories are in good agreement with experimental results before peak deflections and that the improved SDOF model is an acceptable tool for predicting the behavior of HFR-LWC beams under blast loadings accompanying membrane action.     

铝合金-纯铝-钢复合板爆炸焊接试验及性能研究

通过设计爆炸焊接试验复合了铝合金-纯铝-钢爆炸复合板,对其界面形态、显微硬度及力学性能进行了研究。结果表明,铝合金-纯铝界面纯规则正弦波形,纯铝-钢复合板界面波形较小,铝合金-纯铝-钢复合板的界面剪切强度在75 MPa以上,爆炸复合过程中,纯铝与钢界面生成了金属间化合物,其界面处基体金属发生强烈的塑性变形。复合板变形及组织变化的结果造成复合板界面处的显微硬度最高,随着距界面距离的增加,两侧基体金属的硬度逐渐降低。     

激光制备高附着性能的铜基类金刚石膜

提升类金刚石(Diamond-Like Carbon, DLC)膜在被保护基底上的附着能力具有明显的实际应用价值。从微观机理上分析了前期设计的Cu基多层DLC膜有效性的原因。在此基础上,研究了DLC/SiC循环层中两者厚度比例对膜层的附着性能、纳米硬度和耐磨性的影响,以优化结构、进一步提升实际应用所需的膜层性能。纳米划痕和压痕测试结果表明:随着DLC层与SiC层厚度比例的增大,多层DLC膜在Cu基上附着性能逐渐降低,但当厚度比小于2.3时,仍接近厚度400 nm的单层DLC膜在Si基上的附着性能；Cu基多层DLC膜的纳米硬度逐渐提高,同时,耐磨性接近纯DLC膜。